There are 254 products.
Active filters
Light weight shock bushings designed to use with the carbon shock towers(IFW631/IFW632). Not to be used with the aluminum shock towers.
Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.
Spare parts for MP10
High strength and precision construction of molded rear hub delivers improved controllability and better handling char
Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.
FRP main chassi and carbon front upper plate. More rigid flex allows more responsive steering.
Carbon upper deck. More rigid than the FRP version allowing less flex and roll. Great for high traction surface.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
Polycarbonate Wing with gold anodize Wing Holder for FANTOM EP 4WD. Improves rear tire grip by installing it, and stability of straight running and cornering at high speed range are also improved.
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Ride height adjustment spacers for the Fantom EP 4WD and EXT. Can be installed in the front and rear between the axle mount and chassis. Allows 2 different(0.5mm / 1.0mm) lower positions.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
Optional parts for the FANTOM EP 4WD. By replacing 6x15x5mm bearing for wheel shaft with 2pcs 6x10x3mm bearings, reduces shaft vibration and friction loss. Gold anodized finish Bearing Holder. 2 sets included.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
Durable hard front hub carrier set. 17.5 degrees
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
