There are 121 products.
IFW602 Titanium Screw Set...
Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.
IFW339B 3PC HD Aluminum...
Compared to conventional 3pc clutch shoes, durability is greatly improved More accurate for clutch on & off by material change. ※Option parts for INFERNO series.
IFW636 3PC HD LW Aluminum...
Option part for the INFERNO MP10, MP10 TKI2, and MP10T.
Lower weight than the existing aluminum clutch shoes, but stronger acceleration with the refined engagement surface.
Two types of clutch springs, Φ0.9 and Φ0.95 are available for a wider range of clutch settings.
IFS006-1116 Big Shock...
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
IFS006-10516 Big Shock...
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
IFS005-8516 Big Shock...
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
IFS005-816 Big Shock Spring...
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
IFW634-47S Light Weight...
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
IFW634-46S Light Weight...
New light weight 46T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.
IFW634-45S Light Weight...
New light weight 45T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.
IFW632 Carbon Rear Shock...
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
IFW631 Carbon Front Shock...
Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks
IFB023H Body (MP10...
IF625SS Front Lower Sus....
Softer front lower suspension arms for the MP10/10e. Forgiving and withstands impacts with the softer material. Suitable for rough tracks.
IFW626 Carbon Upper Plate
Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.
IFW627 Carbon Center...
Carbon center bulk plate for the MP10. Carbon allows lighter weight without sacrificing durability.
IFW628 Carbon Radio Plate
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
IFW629 Aluminum Front Hub...
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
IF625S HD Front Lower...
Setting parts for INFERNO MP10.
The rigidity and strength of the front arm have been improved by adding ribs and changing the wall thickness.
IFS004-1014 Big Shock...
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
IFS004-10514 Big Shock...
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
IFS004-1114 Big Shock...
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
IFW623 HD Front Shock...
Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
IFW624 HD Rear Shock...
Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
IFW619 Drive Bevel Gear...
Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).
IFW618 Ring Gear (42T/MP10)
Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).
IFW615 HD Cap C-Universal...
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
IFW613 HD Cap U-Swing...
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
IFW612 L/Weight Long Shock...
New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.
IFW611-1 Brass Front Hab...
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
IFW611-0 Brass Front Hab...
New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
IF454B Linkage Set (MP9)
Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.
IFW610 Aluminum Steering...
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
IFW609 Aluminum Steering...
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for Futaba servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
IFW608 Aluminum Rear Hub...
CNC machined aluminum hub carrier for the MP10.
Increases durability and rigitity. Includes bushings for bearing protection.
IFW605-20 Rear Chassis...
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
IFW605-10 Rear Chassis...
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
IFW604-20 Front Chassis...
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
IFW604-10 Front Chassis...
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
IFW603 3PC Clutch Set...
Option parts for the INFERNO MP9 / MP10.
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.
IFW601 Titanium Rod Set (MP10)
Reduces the weight of chassis by using lightweight titanium rods.
Improves steering response and suspension movement. Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.
IFW468B Front Hub Carrier...
Durable hard front hub carrier set. 17.5 degrees