There are 185 products.
Active filters
4 light clear LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
Optional parts for the Fazer MK2 and the FZ02. Convenient tool when installing and removing front hub ball. The ball can be installed straight by tightening the cap screw without damaging the ball, as well as easy removing. Also useful when changing from nylon ball to optional the FAW218 HD ST ball.
Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.
Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.
Optional parts for the Fazer MK2 Touring cars. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.
FAZER Optional parts for Mk2 FZ02-R.
Setting parts for adjusting grip in response to vehicle setup and road surface conditions. Contains 2 pieces of each of 3 types: Soft, Medium (equivalent to standard), and Hard.
Coil inner diameter: 16.5mm, overall coil length: 44mm, wire diameter: 1.1mm.
※You need to purchase two to make one unit.
Contents
Soft (pink / total 9 rolls) ×2
Medium (yellow / total 8 rolls) ×2
Hard (blue / total 7 rolls) ×2
Optional parts for FAZER FZ02-R.
※When used with the FZ02L-BT series, please also use Button Screws (M4x22) (Hex/5 pcs) part No. 1-S14022H.
Ride height adjustment spacers for the Fantom EP 4WD and EXT. Can be installed in the front and rear between the axle mount and chassis. Allows 2 different(0.5mm / 1.0mm) lower positions.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Spare parts for FAZER MAD VAN series and RAGE 2.0
Optional parts for the FANTOM EP 4WD. By replacing 6x15x5mm bearing for wheel shaft with 2pcs 6x10x3mm bearings, reduces shaft vibration and friction loss. Gold anodized finish Bearing Holder. 2 sets included.
4 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
CNC machined aluminum center shaft for FZ02 chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product
Clamp Type Rear Wheel Hub for the FANTOM EP 4WD. Lightweight gold anodized hub & collar set. Prevents damage to shaft due to core deviation and screws.
A type of LED light unit that takes power from the receiver.
Lineup of 2 lights / 4 lights and clear / red. LED can be added by connecting to the attached connector.
Optional parts for the Fazer MK2 and the FZ02. High precision machined servo saver. Improves the steering feel for accurate operation.
CNC machinedC aluminum motor mount. Red anodied motor mount fits all Fazer Mk2 chassis
Spare parts for Mad Bang. This product must be used in combination with FA535-76 Spur Gear 76T FZ02L-B when using EZTH001BKS tires for Rage 2.0.
～ for the full rally experience ～
Rally conversion set for the Fazer MK2 touring cars with short wheelbase. Longer suspension stroke allows off-road driving. Includes longer shocks, shock towers and related parts. Does not come with tire and wheels.
CNC machined 2mm thick carbon upper deck. Achieves increased strength and weight reduction of approximately 5g compared to normal FRP products.
Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.
Aluminum shock set for Fazer MK2 TC chassis.
Includes 2pcs soft springs of #FAW224.
Allows a stable damping force than plastic shocks and fine setting is available with smooth function.
Dial type of height adjustment applys for various range of road surface conditions.
■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO
・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4
Option parts for the Fazer Mk2. CNC machined aluminum front hubs allow precise and linerar steering response and smooth suspensionmovement. Allows camber angle adjustments.
Option parts for the Fazer Mk2. CNC machined aluminum rear hubs allow smoother suspension movement. Allows 2 camber angle adjustments.
