2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.

<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima

Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.

Spare parts for OPTIMA MID

Spare Parts for OPTIMA

Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.

4 light clear LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.  

Spare parts for the IFW615.

New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Designed for 1/10 RWD drift cars. Optional parts for the FAZER D2 drift car. The standard servo horn is made of resin, but upgrading to a CNC-machined aluminum version significantly enhances steering response and holding strength. Additionally, the adjustable design allows fine-tuning of the steering feel by adjusting the arm length from 17mm to 21mm. FAW310 is compatible with Kyosho and Futaba, while FAW311 is compatible with Sanwa and KO.

Spare part for INFERNO MP10 TKI3.

Spare part for INFERNO MP10 TKI3

High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.

Spare parts for OPTIMA MID

CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum

CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.

Spare parts for OPTIMA MID

Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.

22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.

INFERNO MP10 TKI2 Spare parts

4 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets. 

Front shock spring (70mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.

Spare parts for the IFW614.

Durable hard front hub carrier set. 17.5 degrees

Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.

CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product

Spare parts for Optima Mid

Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks

Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.

INFERNO MP10 TKI2 Spare parts

A type of LED light unit that takes power from the receiver.
Lineup of 2 lights / 4 lights and clear / red. LED can be added by connecting to the attached connector.

Front shock spring (70mm) for INFERNO MP10/MP9

Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Reduces the weight of chassis by using lightweight titanium rods. 
Improves steering response and suspension movement.  Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.

Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.

Spare parts for MP10
Front and rear lower suspension arms have been significantly reinforced for greater strength and also designed so they don’t catch dirt for easier cleaning and maintenance. The new arms are also substantially thicker around the large diameter φ4.5mm hinge pins to make the arms even more resilient.

CNC machined 2mm thick carbon upper deck. Achieves increased strength and weight reduction of approximately 5g compared to normal FRP products.

Optional parts for Optima

95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option parts for the INFERNO MP9 / MP10. 
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.

Spare parts for MP10

Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.

Spare parts for Optima Mid

Spare parts for OPTIMA MID

INFERNO MP10 TKI2 Spare parts

Carbon center bulk plate for the MP10. Carbon allows lighter weight without sacrificing durability.

Front shock spring (70mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.

CNC machined aluminum hub carrier for the MP10. 
Increases durability and rigitity. Includes bushings for bearing protection.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Spare parts for MP10

Spare parts for MP10

Spare parts for MP10
Not only does the new 2017S grade engine mount increase rigidity, it improves pitching characteristics and reduces flex of the chassis through jumps.

Spare parts for MP10
The CNC machined 3mm thick 7075 aluminum main chassis is hard anodized (true hard anodizing) to produce a much harder surface for high strength and durability.