There are 223 products.
Active filters
Light weight shock bushings designed to use with the carbon shock towers(IFW631/IFW632). Not to be used with the aluminum shock towers.
Designed for 1/10 RWD drift cars. Optional parts for the FAZER D2 drift car. The standard servo horn is made of resin, but upgrading to a CNC-machined aluminum version significantly enhances steering response and holding strength. Additionally, the adjustable design allows fine-tuning of the steering feel by adjusting the arm length from 17mm to 21mm. FAW310 is compatible with Kyosho and Futaba, while FAW311 is compatible with Sanwa and KO.
1/10 RWD. Optional parts for the drift car FAZER D2.
The standard servo horn is made of resin, but by using machined aluminum, the response and holding power of the steering have been greatly improved.
Additionally, the steering feel can be adjusted by changing the distance between 17mm and 21mm.
FAW310 is for Kyosho and Futaba, while FAW311 is for Sanwa and KO.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks
Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.
Carbon center bulk plate for the MP10. Carbon allows lighter weight without sacrificing durability.
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
A type of LED light unit that takes power from the receiver.
Lineup of 2 lights / 4 lights and clear / red. LED can be added by connecting to the attached connector.
Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).
Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).
Option parts for INFERNO MP10T. Harder suspension arm than standard one to improve hardness. Setting parts according to road surface.
Engraved for identification.
Option parts for INFERNO MP10T. Harder suspension arm than standard one to improve hardness. Setting parts according to road surface.
Engraved for identification.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.
New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Option parts for the INFERNO MP9 / MP10.
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.
Reduces the weight of chassis by using lightweight titanium rods.
Improves steering response and suspension movement. Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.
Durable hard front hub carrier set. 17.5 degrees
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
