There are 220 products.
Active filters
New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.
Spare parts for MP10
Newly designed upper plate delivers improved front traction and steering performance.
Light weight shock bushings designed to use with the carbon shock towers(IFW631/IFW632). Not to be used with the aluminum shock towers.
Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.
Spare parts for MP10
High strength and precision construction of molded rear hub delivers improved controllability and better handling char
Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.
Machined aluminum steering blocks. Available in 0.5°, 1.5°, and 2.5° camber angles, based on the standard 0°. Similar to the MZW702, they feature a realistic design that allows adjustment of the upper arm mounting position and kingpin tilt, just like full-scale vehicles. When combined with the MZW702, fine-tuned adjustments can be made from 0°to 3°in 0.5°increments.
Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)
* This product is not compatible with the MM2 motor case
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Can be installed on MR-03VE, MA-015, MA-020VE and MB-011.
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
Durable hard front hub carrier set. 17.5 degrees
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
Unidirectional edge pattern high-grip tires. Realizes exceptional grip, not just on urethane, but also on carpet surfaces.
■MZW38/10 / MZW38-20 / MZW38-30 / MZW38-40
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
Optional parts for the MR-04. A ball set with three different seat thicknesses designed for the balls mounted on the lower suspension arms. The standard setup includes a 1.0mm plastic spacer, but replacing it with the 1.0mm ball from this set helps prevent the plastic spacer from being lost and also helps prevent the knuckle arms from detaching. The 0.3mm and 0.5mm balls can be combined with plastic spacers to adjust the ride height.
<Contents>
0.3mm ball with seat x 2
0.5mm ball with seat x 2
1.0mm ball with seat x 2
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks
Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.
