There are 217 products.
Active filters
Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
Carbon Rear shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks.
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Carbon Radio plate for the MP10. Carbon allows lighter weight without sacrificing durability.
22 degrees caster angled Aluminum front hub carrier. Compatible with MP10 / MP10 TKI2 / MP10e. Bigger angle increases stability on bumpy tracks.
Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.
Durable hard front hub carrier set. 17.5 degrees
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product
Carbon front shock tower for the MP10 / MP10 TKI2 / MP10e. Designed to use with MP10TKI2 long shocks. Light weight and durable carbon allows lower CG. The slightly more flex feel allows a different feel than the aluminum shock towers. A great setup option for various tracks
Carbon front upper plate for the MP10. Carbon allows lighter weight without sacrificing durability.
95mm Shock Spring for INFERNO MP10/MP10T/MP10e/MP9. It is necessary for Buggy to use together with IFW624 HD Rear Shock Stay.
Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.
Option parts for INFERNO MP10T. Harder suspension arm than standard one to improve hardness. Setting parts according to road surface.
Engraved for identification.
New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Reduces the weight of chassis by using lightweight titanium rods.
Improves steering response and suspension movement. Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.
Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.
Spare parts for MP10
Front and rear lower suspension arms have been significantly reinforced for greater strength and also designed so they don’t catch dirt for easier cleaning and maintenance. The new arms are also substantially thicker around the large diameter φ4.5mm hinge pins to make the arms even more resilient.
CNC machined 2mm thick carbon upper deck. Achieves increased strength and weight reduction of approximately 5g compared to normal FRP products.
Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).
Option parts for the INFERNO MP9 / MP10.
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.
Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.
