There are 276 products.
Active filters
Optional parts for the Fazer MK2 Touring cars. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.
New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.
New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Durable steel rear center shaft cup. Precision CNC machined for heavy duty use.
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
CNC machined aluminum center shaft for FZ02 chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
Option parts for the INFERNO MP9 / MP10.
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.
Reduces the weight of chassis by using lightweight titanium rods.
Improves steering response and suspension movement. Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.
Durable hard front hub carrier set. 17.5 degrees
Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.
Optional parts for Inferno MP10/MP10e/MP10T/MP10Te
Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.
～ for the full rally experience ～
Rally conversion set for the Fazer MK2 touring cars with short wheelbase. Longer suspension stroke allows off-road driving. Includes longer shocks, shock towers and related parts. Does not come with tire and wheels.
Option parts for the Fazer Mk2. CNC machined aluminum front hubs allow precise and linerar steering response and smooth suspensionmovement. Allows camber angle adjustments.
Carbon Front Suspension Arm for the FANTOM EP 4WD. Allows weight reduction and increased rigidity around front parts by replacing FRP upper and lower suspension arms, improves initial steering reaction.
4 light clear LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
Optional parts for the Fazer MK2 and the FZ02. High precision machined servo saver. Improves the steering feel for accurate operation.
Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.
Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.
CNC machinedC aluminum motor mount. Red anodied motor mount fits all Fazer Mk2 chassis
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
CNC machined aluminum center shaft for FZ02L chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
Spare parts for MP10
Not only does the new 2017S grade engine mount increase rigidity, it improves pitching characteristics and reduces flex of the chassis through jumps.
Spare parts for MP10
The CNC machined 3mm thick 7075 aluminum main chassis is hard anodized (true hard anodizing) to produce a much harder surface for high strength and durability.
Optional parts for the FANTOM EP 4WD. By replacing 6x15x5mm bearing for wheel shaft with 2pcs 6x10x3mm bearings, reduces shaft vibration and friction loss. Gold anodized finish Bearing Holder. 2 sets included.
4 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.
■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO
・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4
Option parts for the Fazer Mk2. CNC machined aluminum rear hubs allow smoother suspension movement. Allows 2 camber angle adjustments.
Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.
Polycarbonate Wing with gold anodize Wing Holder for FANTOM EP 4WD. Improves rear tire grip by installing it, and stability of straight running and cornering at high speed range are also improved.
Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.
CNC machined aluminum hub carrier for the MP10.
Increases durability and rigitity. Includes bushings for bearing protection.
Aluminum heat sink for the motor. Keeps motor temperture low efficiently.
Aluminum shock set for Fazer MK2 TC chassis.
Includes 2pcs soft springs of #FAW224.
Allows a stable damping force than plastic shocks and fine setting is available with smooth function.
Dial type of height adjustment applys for various range of road surface conditions.
