Front shock spring (70mm) for INFERNO MP10/MP9

Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

Option parts for INFERNO MP10T. Harder suspension arm than standard one to improve hardness. Setting parts according to road surface.
Engraved for identification.

Spare parts for the MP10T

New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Reduces the weight of chassis by using lightweight titanium rods. 
Improves steering response and suspension movement.  Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.

Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.

Spare parts for MP10
Front and rear lower suspension arms have been significantly reinforced for greater strength and also designed so they don’t catch dirt for easier cleaning and maintenance. The new arms are also substantially thicker around the large diameter φ4.5mm hinge pins to make the arms even more resilient.

Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option parts for the MP10T (for Rear Shock)

Option parts for the MP10T (for Front Shock)

Option parts for the INFERNO MP9 / MP10. 
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.

Spare parts for MP10

Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.

■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO

・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4

Machined aluminum wheel hub. Increased durability.

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

INFERNO MP10 TKI2 Spare parts

Carbon center bulk plate for the MP10. Carbon allows lighter weight without sacrificing durability.

Spare parts for the FANTOM EP 4WD

Spare parts for the FANTOM EP 4WD

Spare parts for the MP10T

Front shock spring (70mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Option parts for the MP10T (for Front Shock)

Option parts for the MP10T (for Front Shock)

Spare parts for the MP10T

Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.

CNC machined aluminum hub carrier for the MP10. 
Increases durability and rigitity. Includes bushings for bearing protection.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Spare parts for MP10

Spare parts for MP10

Spare parts for MP10
Not only does the new 2017S grade engine mount increase rigidity, it improves pitching characteristics and reduces flex of the chassis through jumps.

Spare parts for MP10
The CNC machined 3mm thick 7075 aluminum main chassis is hard anodized (true hard anodizing) to produce a much harder surface for high strength and durability.