Front shock spring (70mm) for INFERNO MP10/MP9

Front shock spring (70mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Rear shock spring (81mm) for INFERNO MP10/MP9

Rear shock spring (85mm) for INFERNO MP10/MP9

Rear shock spring (85mm) for INFERNO MP10/MP9

Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option part for MP10

Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.

Spare parts for the IFW615.

Spare parts for the IFW614.

Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.

New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.

New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

For Mp10, MP9e

Option parts for the INFERNO MP9 / MP10. 
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.

Reduces the weight of chassis by using lightweight titanium rods. 
Improves steering response and suspension movement.  Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.

Durable hard front hub carrier set. 17.5 degrees

Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.

Optional parts for Inferno MP10/MP10e/MP10T/MP10Te

Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Carbon Front Suspension Arm for the FANTOM EP 4WD. Allows weight reduction and increased rigidity around front parts by replacing FRP upper and lower suspension arms, improves initial steering reaction.

Spare parts for the FANTOM EP 4WD

New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Optional parts for the INFERNO MP9/MP10. 
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.

Spare parts for MP10
Not only does the new 2017S grade engine mount increase rigidity, it improves pitching characteristics and reduces flex of the chassis through jumps.

Spare parts for MP10
The CNC machined 3mm thick 7075 aluminum main chassis is hard anodized (true hard anodizing) to produce a much harder surface for high strength and durability.

Optional parts for the FANTOM EP 4WD. By replacing 6x15x5mm bearing for wheel shaft with 2pcs 6x10x3mm bearings, reduces shaft vibration and friction loss. Gold anodized finish Bearing Holder. 2 sets included.

Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.

■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO

・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.

Polycarbonate Wing with gold anodize Wing Holder for FANTOM EP 4WD. Improves rear tire grip by installing it, and stability of straight running and cornering at high speed range are also improved.

Spare parts for the FANTOM EP 4WD

Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.

CNC machined aluminum hub carrier for the MP10. 
Increases durability and rigitity. Includes bushings for bearing protection.

Spare parts for MP10