Rear shock spring (85mm) for INFERNO MP10/MP9

Rear shock spring (85mm) for INFERNO MP10/MP9

Optional parts for INFERNO MP10. Front Shock Stay for IF484 MS Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

Optional parts for INFERNO MP10. Rear Shock Stay for IS215 Shock set.
Changed the existing shock mounting hole position to upper side.
Allows a longer shock travel than standard, which improves the performance when landing of jumps and bumpy section.

Spare parts for 1/10 Turing cars

Spare parts for the Fazer Mk2 Touring Car

Spare parts for the Fazer Mk2 Touring Car

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option parts for INFERNO MP9/MP10 series. Necessary to use together with IFW618 and IFW619 as a set. Improves the throttle feeling to change the secondary reduction ratio (43T / 13T → 42T / 12T).

Option part for MP10

Optional parts for the Fazer MK2 and the FZ02. Convenient tool when installing and removing front hub ball. The ball can be installed straight by tightening the cap screw without damaging the ball, as well as easy removing. Also useful when changing from nylon ball to optional the FAW218 HD ST ball.

Optional parts for Fazer MK2 FZ02L-B (Rage 2.0). Adapter for attaching the OT252 wing. When installs the wing, improves stability at high speed running.

Durable steel front center shaft cup. Precision CNC machined for heavy duty use.

Durable diff shafts.

Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.

Sway bar set for the Fazer Mk2 series. Adjust the roll charateristics for more efficient cornering.

Spare parts for the IFW615.

Spare parts for the IFW614.

Optional parts for the INFERNO MP10.
By covering the joint part of the universal swing shaft with an aluminum cap, it has the effect of preventing splashing of grease and improved durability, as well as protecting a damage from dust.
It also protects the pins from falling off in case of damaging the joint parts.

Option parts for the Rage / Fazer Mk2 chassis. CNC machined aluminum 75T spur gear. Best for high power motors

Optional parts for the Fazer MK2 Rage 2.0. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.

Optional parts for the Fazer MK2 Touring cars. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.

New Light weight long shock bushings sets the shock 3mm to the rear. This angle on the rear shocks improves the shock movement performance drastically and increases traction.

New 0 degrees hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

Durable steel rear center shaft cup. Precision CNC machined for heavy duty use.

Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for KO/Sanwa servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

CNC machined aluminum center shaft for FZ02 chassis. Durable precision made center shaft for high power motors / high gear ratio setups.

For Mp10, MP9e

Option parts for the INFERNO MP9 / MP10. 
Whole set for clutch parts. Easy to purchase some necessary clutch parts when preparing the spare engine.

Reduces the weight of chassis by using lightweight titanium rods. 
Improves steering response and suspension movement.  Includes Upper Rods for Front & Rear, Steering Tie Rods and Steering Servo Rod, 7pcs in total.

Durable hard front hub carrier set. 17.5 degrees

Unidirectional edge pattern high-grip tires. Realizes exceptional grip, not just on urethane, but also on carpet surfaces.
■MZW37-20 / MZW37-30 / MZW37-40

Spring set for adjusting hardness of rear suspension. Includes 3 different hardness types.■Length：23mm

Optional parts for the INFERNO MP10.
Hard type suspension arm increases response and rigidity. Allows easy control when landing.

Optional parts for Inferno MP10/MP10e/MP10T/MP10Te

Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.

Option parts for the Fazer Mk2. CNC machined aluminum front hubs allow precise and linerar steering response and smooth suspensionmovement. Allows camber angle adjustments.

Carbon Front Suspension Arm for the FANTOM EP 4WD. Allows weight reduction and increased rigidity around front parts by replacing FRP upper and lower suspension arms, improves initial steering reaction.

Spare parts for the FANTOM EP 4WD

4 light clear LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.  

Optional parts for the Fazer MK2 and the FZ02. High precision machined servo saver. Improves the steering feel for accurate operation.

Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.

Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.

CNC machinedC aluminum motor mount. Red anodied motor mount fits all Fazer Mk2 chassis

New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.

CNC machined aluminum center shaft for FZ02L chassis. Durable precision made center shaft for high power motors / high gear ratio setups.

Optional parts for the INFERNO MP9/MP10. 
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.

Spare parts for MP10
Not only does the new 2017S grade engine mount increase rigidity, it improves pitching characteristics and reduces flex of the chassis through jumps.

Spare parts for MP10
The CNC machined 3mm thick 7075 aluminum main chassis is hard anodized (true hard anodizing) to produce a much harder surface for high strength and durability.

Optional parts for the FANTOM EP 4WD. By replacing 6x15x5mm bearing for wheel shaft with 2pcs 6x10x3mm bearings, reduces shaft vibration and friction loss. Gold anodized finish Bearing Holder. 2 sets included.

4 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets. 

Spare parts for the Fazer Mk2 Touring Car

Reciver unit for the MINI-Z EVO chassis. 
Supports the KT-531 and KT432PT transmitters.

A tool set suitable for MINI-Z. Improved tool tip shape and various usable tools included!Comes with a soft case with a MINI-Z logo.

- Nut driver: 3.5mm, 4.0mm, 4.5mm
- Philips screwdriver: #00, #0, #1
- Hex screwdriver: 1.5mm

Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.

Optional parts for MR-04 EVO2

Optional parts for MR-04 EVO2

■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO

・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4

Option parts for the Fazer Mk2. CNC machined aluminum rear hubs allow smoother suspension movement. Allows 2 camber angle adjustments.

Spare parts for FAZER RAGE 2.0

Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)

* This product is not compatible with the MM2 motor case