There are 126 products.
Active filters
2 light halogen LED and 2 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
CNC machined aluminum center shaft for FZ02L chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
4 light clear LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
4 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.
Durable steel front center shaft cup. Precision CNC machined for heavy duty use.
Sway bar set for the Fazer Mk2 series. Adjust the roll charateristics for more efficient cornering.
Optional parts for the Fazer MK2 Rage 2.0. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.
Ball differentials for the Fazer Mk2. Lighter(30g) than the stock gear diffs and also the plastic gears have less noise. Ball diffs have smoother cornering and more stable accelaration feel. Requires 2pcs for 1 chassis. Includes ball diff grease and Molybden grease.
Spare parts for the Fazer D2(Short size). The body mount is for the short size Fazer D2 body types. Standard overhang bodies will require the FA617 body mounts.
Optional parts for Fazer MK2 FZ02L-B (Rage 2.0). Adapter for attaching the OT252 wing. When installs the wing, improves stability at high speed running.
Option parts for the Rage / Fazer Mk2 chassis. CNC machined aluminum 75T spur gear. Best for high power motors
Durable steel rear center shaft cup. Precision CNC machined for heavy duty use.
Aluminum heat sink for the motor. Keeps motor temperture low efficiently.
1/10 RWD. Optional parts for the drift car FAZER D2.
The standard servo horn is made of resin, but by using machined aluminum, the response and holding power of the steering have been greatly improved.
Additionally, the steering feel can be adjusted by changing the distance between 17mm and 21mm.
FAW310 is for Kyosho and Futaba, while FAW311 is for Sanwa and KO.
Carbon bumper brace for FZ02 / 02L chassis. Supports bumper and increases chassis rigidity.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
A type of LED light unit that takes power from the receiver.
Lineup of 2 lights / 4 lights and clear / red. LED can be added by connecting to the attached connector.
Optional parts for the Fazer MK2 and the FZ02. Convenient tool when installing and removing front hub ball. The ball can be installed straight by tightening the cap screw without damaging the ball, as well as easy removing. Also useful when changing from nylon ball to optional the FAW218 HD ST ball.
Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.
Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.
Optional parts for the Fazer MK2 Touring cars. Universal Swing shafts to replace the Swing shafts. Protects faling off the shafts when crash and improves drive efficiency.
FAZER Optional parts for Mk2 FZ02-R.
Setting parts for adjusting grip in response to vehicle setup and road surface conditions. Contains 2 pieces of each of 3 types: Soft, Medium (equivalent to standard), and Hard.
Coil inner diameter: 16.5mm, overall coil length: 44mm, wire diameter: 1.1mm.
※You need to purchase two to make one unit.
Contents
Soft (pink / total 9 rolls) ×2
Medium (yellow / total 8 rolls) ×2
Hard (blue / total 7 rolls) ×2
Optional parts for FAZER FZ02-R.
※When used with the FZ02L-BT series, please also use Button Screws (M4x22) (Hex/5 pcs) part No. 1-S14022H.
Designed for 1/10 RWD drift cars. Optional parts for the FAZER D2 drift car. The standard servo horn is made of resin, but upgrading to a CNC-machined aluminum version significantly enhances steering response and holding strength. Additionally, the adjustable design allows fine-tuning of the steering feel by adjusting the arm length from 17mm to 21mm. FAW310 is compatible with Kyosho and Futaba, while FAW311 is compatible with Sanwa and KO.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Spare parts for FAZER MAD VAN series and RAGE 2.0
CNC machined aluminum center shaft for FZ02 chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product
Optional parts for the Fazer MK2 and the FZ02. High precision machined servo saver. Improves the steering feel for accurate operation.