There are 216 products.
Active filters
Spare parts for MP10
Front and rear lower suspension arms have been significantly reinforced for greater strength and also designed so they don’t catch dirt for easier cleaning and maintenance. The new arms are also substantially thicker around the large diameter φ4.5mm hinge pins to make the arms even more resilient.
Spare parts for MP10
Based on the suspension geometry of the MP9 TKI4 shock stay, the number of shock and upper arm mounting holes has been optimized. In addition, the reinforced rear shock stay delivers increased strength and prevents dirt catching.
Spare parts for MP10
Based on the suspension geometry of the MP9 TKI4 shock stay, the number of shock and upper arm mounting holes has been optimized. In addition, the reinforced rear shock stay delivers increased strength and prevents dirt catching.
Spare parts for MP10
Newly designed upper plate delivers improved front traction and steering performance.
Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.
Compared to conventional 3pc clutch shoes, durability is greatly improved More accurate for clutch on & off by material change. ※Option parts for INFERNO series.
Option part for the INFERNO MP10, MP10 TKI2, and MP10T.
Lower weight than the existing aluminum clutch shoes, but stronger acceleration with the refined engagement surface.
Two types of clutch springs, Φ0.9 and Φ0.95 are available for a wider range of clutch settings.
2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.
<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima
Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.
New light weight 46T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.
New light weight 45T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.
Optional parts for the INFERNO MP10/MP9e Evo.
New setting weights by 10g and 20g which can be installed the main chassis.
Can be adjusted the weights in 10g/20g/30g/40g by weights combination.
Fixing by screws and nylon nut which prevents falling off when driving.
Use for front tires on MINI-Z Racer and MINI-Z AWD. Reduces sticking on urethane surfaces for smooth running characteristics.
Spare parts for MP10
High strength and precision construction of molded rear hub delivers improved controllability and better handling char
Unidirectional edge pattern high-grip tires. Realizes exceptional grip, not just on urethane, but also on carpet surfaces.
■MZW38/10 / MZW38-20 / MZW38-30 / MZW38-40
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
Optional front springs for the MP10/MP10e. Thicker and more coil turn allowing stiffer characteristics. Best for high speed and high traction surfaces.
CNC machined 2mm thick carbon upper deck. Achieves increased strength and weight reduction of approximately 5g compared to normal FRP products.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Can be installed on MR-03VE, MA-015, MA-020VE and MB-011.
Use for front tires on MINI-Z Racer and MINI-Z AWD. Reduces sticking on urethane surfaces for smooth running characteristics.
Unidirectional edge pattern high-grip tires. Realizes exceptional grip, not just on urethane, but also on carpet surfaces.
■MZW38/10 / MZW38-20 / MZW38-30 / MZW38-40
Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.
Spare parts for MP10
Increased durability and reliability is achieved with larger φ4.5mm diameter inner hinge pins compared to the φ4.0mm hinge pins on the MP9 TKI4.
Optional parts for the MR-04. A ball set with three different seat thicknesses designed for the balls mounted on the lower suspension arms. The standard setup includes a 1.0mm plastic spacer, but replacing it with the 1.0mm ball from this set helps prevent the plastic spacer from being lost and also helps prevent the knuckle arms from detaching. The 0.3mm and 0.5mm balls can be combined with plastic spacers to adjust the ride height.
<Contents>
0.3mm ball with seat x 2
0.5mm ball with seat x 2
1.0mm ball with seat x 2
Machined aluminum steering blocks. Available in 0.5°, 1.5°, and 2.5° camber angles, based on the standard 0°. Similar to the MZW702, they feature a realistic design that allows adjustment of the upper arm mounting position and kingpin tilt, just like full-scale vehicles. When combined with the MZW702, fine-tuned adjustments can be made from 0°to 3°in 0.5°increments.
Light weight shock bushings designed to use with the carbon shock towers(IFW631/IFW632). Not to be used with the aluminum shock towers.
Optional parts for Inferno MP10/MP10e/MP10T/MP10Te
