There are 839 products.
Unidirectional edge pattern high-grip tires. Realizes exceptional grip, not just on urethane, but also on carpet surfaces.
■MZW38/10 / MZW38-20 / MZW38-30 / MZW38-40
Optional Parts for the MP10/MP9 series. High precision Alumimum Steering Horn for Futaba servos. It is 2mm shorter than existing aluminum steering servo horns, and the initial reaction of corner tends to be mild and easy to drive.
Optional parts for the INFERNO MP10.
Approximately 34g lighter in total than standard steel screws.
Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)
* This product is not compatible with the MM2 motor case
■Length 450mm
■Width 195mm(Body width:196mm)
■Height 136mm
■Chassis Height 8mm(approx.)
■Wheelbase 260mm
■Tread (F/R) 167mm
■Tires (F/R) φ64×27.7mm
■Gear Ratio 6.54：1
■Weight 1650g (approx.)
■R/C system &; Syncro KT-231P+
■Motor G14L
<Kit Contents>
●Completed chassis with R/C radio installed
●Factory assembled body complete with color scheme
●Syncro KT-231P+ transmitter
●Hexagonal wrench
●Spanner
●Setting change parts
<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tools
Aluminum front hub carrier. Provides increased rigidity and better appearance.
Aluminum knuckles. Provides increased rigidity and better appearance.
Internal resistance: 0.0011Ω
Continuous maximum current: 60A
Instantaneous maximum current: 80A
Maximum KV value (2S): 13.5T 3200KV
Driving mode: Forward / brake / forward / brake / reverse
Input voltage: 7.2V-11.1V
Compatible motor type: Sensor & Sensorless
BEC output: 6V / 2A
size (mm): 37.5 x 30.8 x 18.7
Weight (g): Approximately 80
LiPo power at a budget price from ANTIX by LRP.
These RC car LiPos are ideal for hobby and amateur drivers looking for power and durability at a budget price.
The special "stickpack" shape is based on the NiMh packs for which many chassis were designed.
Also for the new release of vintage models you get perfectly fitting batteries of the latest technology with 134mm length and additionally slightly offset cable exit, so the battery posts of your chassis do not get in the way.
Equipped with a robust hard case, these 2S LiPo batteries are suitable for tough On- and Offroad use.
※It is not possible to drive with auto scale alone. In addition, some bodies cannot be mounted depending on the chassis.
※The optional part No. MZW411B friction damper set cannot be installed because it interferes with a part of the body.
■Length 455mm
■Width（Body width） 200mm（210mm）
■Height 120mm
■Wheelbase 260mm
■Tread (F/R) F：174mm／R：174mm
■Tires (F/R) F：φ64×24.2mm／R：φ64×24.2mm
■Gear Ratio 6.54：1
■Weight 1650g(approx.)
■Syncro KT-231P+ transmitter
■Motor G14L
Carbon AMB Holder for the MP9/MP10. made from precision high quality carbon material.
* You cannot drive with the auto scale alone. In addition, some bodies cannot be mounted due to the chassis.
* The optional part No. MZW411B friction damper set cannot be installed because it interferes with a part of the body.
Carbon Front Suspension Arm for the FANTOM EP 4WD. Allows weight reduction and increased rigidity around front parts by replacing FRP upper and lower suspension arms, improves initial steering reaction.
・AL case
・Compatible with SXR
・New Function: Quick-ST
・Compatible with setting by MULTI-SETTING GEAR
Machined brass front hub. Increases the weight distribution on the front wheels for improved uphill performance.
A type of LED light unit that takes power from the receiver.
Lineup of 2 lights / 4 lights and clear / red. LED can be added by connecting to the attached connector.
●FH5U: SXR(SANWA XTREME RESPONSE) MODE-COMPATIBLE
●SSL-COMPATIBLE PROGRAMMABLE SERVO
# Compatible with CODE 10 (M12S, EXZES ZZ, MT-44)
Not Compatible with CODE 5 (M12, EXZES Z, MT-4S, MT-4, MT-S)
●PGS SETTING GEAR-COMPATIBLE
●SUPER RESPONSE (SSR) MODE-COMPATIBLE
●HIGH RESPONSE (SHR) MODE-COMPATIBLE
●Li-Po 2 CELL-COMPATIBLE
●LOW PROFILED
●HIGH SPEED TYPE
●BRUSH LESS MOTOR
●FULL ALUMINUM CASE
●FULL METAL GEAR (Strengthening Gears)
●AL HEAT SINK
●Black Harness
Compact receiver
Waterproof
Plug in Bind
Short Coaxial Antenna
●2.4 GHz FHSS5 Spread Spectrum System 4ch
●Compatible with Telemetry
※Cannot connect RPM sensor and Temperature sensor
To measure RPM and Temperature is only
combine with SUPER VORTEX series
●Compatible with SSL (SUPER VORTEX Series, etc...)
●Ultra Response Mode (SUR)
●Extreme Response Mode (SXR)
●Waterproof
●The smallest and most light receiver in the class
■Length 595mm
■Width 220mm
■Height 350mm
■Weight 1,600g approx.
■Transmitter KT-231P+
■ESC KYOSHO SPEED HOUSE
KA060-91W
■Servo KS4031-06W
■Motor 550-class G14L motor with water-cooling jacket
■Battery 7.2V-2200mAh NiMH
■Compatible battery size L148xW52xH30mm or less
■Charger Ni-MH battery dedicated USB charger
■Propeller D31xP1.4 (Polycarbonate)
■Maximum speed 24km/h approx.
■Operation time 5 min approx.
Optional parts for the Fazer MK2 and the FZ02. High precision machined servo saver. Improves the steering feel for accurate operation.
Optional parts for the Fazer MK2 FZ02L-B (Rage 2.0). Durable wheel hubs.
■Length 507mm
■Width 195mm(Body width:210mm)
■Wheelbase 274mm
■Tread (F/R) F：167mm／R：167mm
■Tires (F/R) F：φ64×27.7mm／R：φ64×27.7mm
■Gear Ratio 6.54：1
■Weight 1650g (approx.)
■R/C system Syncro KT-231P+
■Motor G14L
Optional parts for the Fazer MK2 and the FZ02. High precision stainless steel machined ball for front hub. Improves the durability.
CNC machinedC aluminum motor mount. Red anodied motor mount fits all Fazer Mk2 chassis
Durable die-cast center gear to beef up the drive train.
New 1 degree hub carrier brass bushing inserts for the Inferno MP9 / 10. Increased durability and more weight to increase traction.
Pit mat with cool MINI-Z logos.
Great for maintanance of your MINI-Z while keeping the pit table clean.
Soft and grippy PVC material avoids small parts to fall off the table.
Size: 24 in. x 17 in. (approx 600 x 430mm).
CNC machined aluminum center shaft for FZ02L chassis. Durable precision made center shaft for high power motors / high gear ratio setups.
Light weight 2.5mm and 2.0mm suspension plates. Compared to the stock aluminum plates the carbon fiber plates are 2g lighter and with the same durability.
Optional parts for the INFERNO MP9/MP10.
Currently line-up from 2.1mm to 2.8mm by 0.1mm difference. Add new item by 2.9mm to increase setting variety.
■Length 395mm
■Width 244mm
■Height 120mm
■Wheelbase 260mm
■Front Tread 208mm
■Rear Tread 208mm
■Weight 1,600g (approx.)
■Tires (F/R) φ82×36mm
■Motor 540 class size (sold separately)
■Gear ratio 9.24 : 1
Turns：15.5Ｔ
Operating Voltage：1-3Ｓ／12.6Ｖ
RPM@7.4V：18870
KV（RPM／V）：2550
Max Current：38A
Max Power：320W
Efficiency：90％
Weight（g）：179
Motor Diameter（mm）：35.8
Motor Length（mm）：51.2
Shaft Length（mm）：15
Shaft Diameter（mm）：3.175
