There are 1573 products.
Spare parts for the TURBO OPTIMA.
Optional parts for the OPTIMA and JAVELIN.
Optional parts for the TURBO OPTIMA.
When use with #OTH245W, it can be used as optional parts for the OPTIMA and JAVELIN.
■Length 472mm
■Width 350mm
■Height 198mm
■Wheelbase 295mm
■Tread F/R 278mm
■Tires（F & R） φ128 x 70mm
■Gear Ratio 15.22：1
■Weight 3,610g (approx.)
■Motor TORX10L Brushless Motor kv2850
<Readyset Contents>
●Factory assembled chassis complete with control linkages
●Pre-cut and painted body complete with decals applied
●2.4GHz Syncro KT-231P+ transmitter
●1.5mm/2.0mm/2.5mm L shaped hex wrench
●Cross wrench
●4/5/5.5/7/10mm Integrated spanner
<Required to operate>
●AA-size batteries x 4 for transmitter
●Battery for driving (2-3S LiPo battery *Installable battery size 143x47x30mm)
●Charger for LiPo battery
Greatly suppresses vibration and instability of steering control. Increases stability during high speed cornering, acceleration and braking.
■Length 193mm
■Width 84mm
■Height 90.0mm
■Chassis Type MX-01
■Wheel Base 120mm
■Tread F/R:72.7mm
■Weight 242g (excl. battery)
■Motor/Engine 130 Class
■Gear Ratio 55.44：1/46.20：1/39.60：1
39.60：1/34.65：1/34.65：1
■Front Tire Diameter Φ37.0mm
■Rear Tire Diameter Φ37.0mm
■Front Tire Width 12mm
■Rear Tire Width 12mm
■Battery 4 x AAA Alkaline
■Transmitter Syncro KT-531P
■Speed：Approx. 2.7km/h〜5.4km/h (Pinion gears 10T〜 20T)
■Running Time Approx. 60 mins
<Kit Content>
●Complete chassis with built-in electronics.
●Factory-painted body complete with many fine details
●KT-531P 2.4GHz transmitter
●Pinion gear set（10T、12T、14T、16T、18T、20T）
●3 types of pinion gear spacers
Option parts for the TURBO OPTIMA.
Soft compound of 50mm tire. For low grip road surface
■Length 660mm
■Width 160mm
■Height 325mm
■Weight 1,530g approx.
■Motor 550-class G14L motor with water-cooling jacket
■propeller Size D31 x P1.4 (polycarbonate)
■Maximum Speed 21km/h approx.
■Operation time 5 minutes 30 seconds approx.
＜ Kit Contents ＞
●Pre-colored surf board installed with R/C system, complete with linkages
●Complete pre-painted surfer figure
●KT-231P+2.4GHz 2ch pistol grip type transmitter
●7.2V-22HV NiMH battery
●Ni-MH battery dedicated delta peak USB charger
●Styrofoam slipway
●Spare ladder
＜ Required for Operation ＞
●AA batteries x 4 for transmitter
Back plate for the KE21 SP / KE25SP / KE25SP2 engine. Back plate elimintes the pull start allowing the use of starter boxes. Less friction allows more performance.
Optional parts for INFERNO MP10e. Battery spacer for short LiPo batteries.
It is getting popular to use the shorty LiPo batteries to 1/8 EP Buggy due to the improved performance. The battery can be changed the installing position in the battery holder to adjust a center of gravity and balance as well as making weight reduction. That are advantage to use with the shorty LiPo battery. When use the shorty battery to MP10e, it has same effect for car. It can also be used with vintage Scorpion, Beetle and Fazer series.
Lightweight Carbon Rear Shaft for the FANTOM EP 4WD. Improves throttle response by lighter rotating parts. The screw part at tip of differential side is assembled with aluminum parts by factory. Recommended to use with EFW003.
Tie-rod set for the MA-03F/MA-030. Provides four steps of toe angle setup for each narrow and wide configuration.
<Readyset Contents>
●Fully assembled and painted chassis
●3ch transmitter
<Required for Operation>
●1 x PP3 9V alkaline battery for transmitter
●4 x AAA alkaline batteries for model
■Length 595mm
■Width 220mm
■Height 350mm
■Weight 1,600g approx.
■Transmitter KT-231P+
■ESC KYOSHO SPEED HOUSE
KA060-91W
■Servo KS4031-06W
■Motor 550-class G14L motor with water-cooling jacket
■Battery 7.2V-2200mAh NiMH
■Compatible battery size L148xW52xH30mm or less
■Charger Ni-MH battery dedicated USB charger
■Propeller D31xP1.4 (Polycarbonate)
■Maximum speed 24km/h approx.
■Operation time 5 min approx.
■Length 595mm
■Width 220mm
■Height 350mm
■Weight 1,600g approx.
■Transmitter KT-231P+
■ESC KYOSHO SPEED HOUSE
KA060-91W
■Servo KS4031-06W
■Motor 550-class G14L motor with water-cooling jacket
■Battery 7.2V-2200mAh NiMH
■Compatible battery size L148xW52xH30mm or less
■Charger Ni-MH battery dedicated USB charger
■Propeller D31xP1.4 (Polycarbonate)
■Maximum speed 24km/h approx.
■Operation time 5 min approx.
Optional parts for the INFERNO MP9/MP10.
Allows to change the inside center differential gear ratio from 10T/20T to 12T/18T.
By changing the differential effect, improve running stability on bumpy track
Increased a setting variety.
Spare parts for Javelin. Compatible with the Optima to use the Javelin roll cage body.
Light weight 2.5mm carbon fiber shock tower. Compared to the stock aluminum shock tower the carbon fiber shock tower is much lighter and with the same durability
Light weight 2.0mm carbon fiber side plates. 5g lighter without compromising the durability.
Light weight 2.5mm carbon fiber plate. Same durability as the stock plates but 5g lighter.
Optional parts for the TURBO OPTIMA.
Color variation of 50mm wheel.
When use with #OTT244M, it can be used as optional parts for the OPTIMA and JAVELIN.
3 types of wire diameters can be chosen for both front and rear. Provides a wide range of setting options
■Length 430mm
■Width 197mm
■Ground Clearance 5mm approx.
■Wheelbase 270mm
■Tread (F/R) 164mm / 166～172mm
■Wheel（F/R） Φ36mm x 30mm / Φ36mm x 45mm
■Weight 1,100g approx.
■Motor Brushless (sold separately)
Required for operation
●2-channel, 1 servo R/C system for cars
●Brushless motor
●ESC for brushless motor
●Battery
●Battery charger for chassis battery
●Tires
●1/10 Formula car body
●Tools
●Paint for body
●Batteries for R/C system
