■Length 507mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.70：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

＜Readyset Contents＞
●Factory assembled chassis complete with control linkages
●Finished body complete with printed color scheme
●2.4GHz Syncro KT-231P+ transmitter
●Break in ring
●1.5、2.0、2.5、3.0mm L shaped hex wrenches
●Cross wrench
●17mm wheel wrench

<Required for Operation>
●Glow fuel
●8 x AA size alkaline batteries for transmitter and receiver
●Engine starting tools (fuel bottle, plug heater)
●Tool

■Length 507mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.70：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

＜Readyset Contents＞
●Factory assembled chassis complete with control linkages
●Finished body complete with printed color scheme
●2.4GHz Syncro KT-231P+ transmitter
●Break in ring
●1.5、2.0、2.5、3.0mm L shaped hex wrenches
●Cross wrench
●17mm wheel wrench

<Required for Operation>
●Glow fuel
●8 x AA size alkaline batteries for transmitter and receiver
●Engine starting tools (fuel bottle, plug heater)
●Tool

For the MR-04 EVO2 chassis. Friction shock for the MR-04MM, featuring carbon plates. It contributes to improved vehicle stability at high speeds. The set includes three springs of varying stiffness levels. The friction shock is compatible with the standard pitching shock and the MZW432B rear oil shock. It can also be used with the MZW708 aluminum oil shock mount.

Optional parts for the 1/8 Inferno MP10 Buggy series. The standard knuckle has a kingpin angle of 0°, while this set features knuckles with 7°kingpin angle. This design reduces front tire catching, particularly in high-speed corners, allowing for higher cornering speeds. It also improves stability, enabling the vehicle to better absorb sudden movements caused by surface gaps or irregularities.

■Length 660mm
■Width 310mm
■Height 180mm
■Wheelbase 360mm
■Tread (F/R) 262mm／265mm
■Tire (F/R)  Φ97mm ×40mm
■Gear Ratio 1st gear /10.14:1　2nd gear /7.49:1
■Weight 3,660g（approx. ）
■Engine　KE25SP2
■Transmitter　Syncro KT-331P

<Kit Content>
●Pre-assembled chassis installed with 2-ch, 2-servo R/C system and pre-set control linkages
●Pre-painted factory assembled body with decals applied
●Installed KE25SP2 rear exhaust engine
●Installed polished tuned muffler
●Syncro KT-331P transmitter
●Hex wrenches: 1.5, 2.0, 2.5, 3.0mm
●Cross wrench (large)
●17mm wheel wrench
●Nylon strap (for air cleaner)
●Break in ring
●Bind code

<Require to run>
●8 x AA batteries for transmitter (4) and receiver (4)
●Fuel
●Engine starting tools (fuel bottle, plug heater)

Aluminum motor mount for the MR-03LM.
High precision machined product made in Japan.
Highly balanced left-right weight distribution contributes to superior traction.
The design supports the LL (98mm) wheelbase as well.  Works best with the MZW310 Inner Tube Roll Shock Set.

Spare parts for MR-04 EVO2

Optional parts for MR-04 EVO2

Optional parts for MR-04 EVO2

Spare parts for MR-04 EVO2

■Length 469mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.56：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

■Length 469mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.56：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

<Readyset Contents>
●Factory assembled chassis complete with control linkages
●Finished body complete with printed color scheme
●2.4GHz Syncro KT-231P+ transmitter
●1.5、2.0、2.5、3.0mm L shaped hex wrenches
●Cross wrench
●17mm wheel wrench

■Length　490mm
■Width　307mm
■Height　180mm
■Ground Clearance　28mm
■Wheelbase　325mm (4 settings available by changing rear hub collar position)
■Tread (F/R)　254mm (2 front settings and 3 rear settings available by changing bushes)
■Tire (F/R)　φ116 x 44mm
■Gear Ratio　11.7:1
■Weight　3,370g approx.
■Engine　KE21SP (recoil starter installed/rear exhaust)

<Kit Content>
●Factory assembled chassis installed with R/C system
●Printed pre-cut body complete with coloring
●Pre-installed KE21SP engine with rear exhaust
●Syncro KT-331P transmitter
●1.5, 2.0, 2.5mm Hexagonal wrench
●Cross wrench (small)
●17mm Wheel wrench

<Require to run>
●AAA x 8 alkaline batteries for transmitter
●Fuel
●Starting tools (Fuel bottle, Plug heater)

■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO

・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4

■Length　490mm
■Width 　307mm
■Height 　180mm
■Ground clearance　28mm
■Wheelbase　325mm 
■Tread（Ｆ／Ｒ）　254mm
■Tires（Ｆ／Ｒ）　sold separately
■Gear Ratio　11.7：1
■Weight　3,360g(approx.)
■Engine　21Class (sold separately)

＜Kit Contents＞
●Unassembled chassis kit
●Special wheels
●Wing
●Special clear body
●Window mask seal
●Logo decals
●Fuel tube
●Linkage parts
●Clutch parts
●Air cleaner
●Ring gear grease
●1.5, 2.0, 2.5mm Hexagonal wrench
●Cross wrench 
●Wheel wrench

＜Required for Operation＞
●2-channel 2-servo R/C system for cars
●Compatible batteries for R/C system
●21 engine
●Muffler
●Tires w/foam inserts for 1/8 buggy
●Starter box
●Plug heater
●Fuel
●Fuel bottle
●Oil for air cleaner
●Shock oil
●Diff oil
●Paint for car body
●Tools

■Length　375mm
■Width　200mm
■Wheelbase　258mm
■Tread (F/R)　176mm
■Tire(F/R)　φ66×25mm
■Gear Ratio　7.47 / 5.44：1
■Weight　1,800g (approx.)
■Engine KE15SP with recoil starter
■Max Speed 64Km(approx.)

<Kit Contents>
●chassis kit
●FAT701M TC Tire (M)＆Inner sponge、VZH003BK  Wheel（not glued）
●Pre-mounted KE15SP engine with recoil starter
●Setting change parts
●1.5mm/2.0mm/2.5mm/5.0mm Hex wrench
●Cross wrench
●3/4/5/5.5/7/8mm Spanner

<Required to run>
●2ch R/C car transmitter
●Body
●Servos x 2
●4 x AA sized alkaline batteries for receiver and Battery Holder or Battery
●4 x AA sized alkaline batteries for transmitter
●Switch
●Silicon oil for Shock
●Silicon oil for diff
●Grease
●GP Starting Tool Set
●Fuel Bottle
●Glow Fuel
●Tool

Option parts for the Fazer Mk2. CNC machined aluminum rear hubs allow smoother suspension movement. Allows 2 camber angle adjustments.

Spare parts for FAZER RAGE 2.0

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)

* This product is not compatible with the MM2 motor case

High RPM and torque .21 size big block engine. Easy to tune with recoil starter.

*This product does not come with a break-in ring.When you break in, please use the accessories that came with the Readyset when you purchased it.

Gyro unit for MINI-Z readyset. Compatible with blue board RC units, or green board RC units with a blue marking on the gyro connector.

Correspondence table

Complete body set for the Inferno GT2. Licensed 2020 Mercedes AMG GT3 body. Wheelbase : 360mm / Body Dimensions : 661 x 310 x 164mm(With rear wing)

■Length: 998mm
■Width: 226mm
■Height: 1,850mm
■Weight: 3,100g
■R/C System: Syncro KT-431S, 2.4GHz, FHSS
■Sail Area: 39dm2
■Servo: Sail KS9071-20SW（waterproof）/　Rudder KS4031-06W

＜Readyset Contents＞
●Pre-colored fully assembled hull
●Syncro KT-431S 2.4GHz R/C system installed
●Folding wood boat stand
●Mast Assy
●Decal for Sail
●Painted Rudder, Keel & Ballast

＜Required for operation ＞
●8 x AA sized batteies for transmitter/receiver (4 for transmitter, 4 for receiver)

Mini steering servo for the Hang On Racer. Bolt on ready. 150mm wire with JR type no flange connector housing. Screw and aluminum collar included.

Option parts for the TURBO OPTIMA.
Soft compound of 50mm tire. For low grip road surface

[Contents]
・ Motor checker body
・ Power cable with super plug ・
O-ring for fixing motor x2 (1 is spare)
・ Rotation adapter x2 (1 is spare)
・ Wiring cable with alligator clip for brush motor
・ Instruction instructions book

[Items that need to be purchased separately] -Battery
motor or brushless motor for minutes (measurement target)
-Battery with super plug from 5.5V to 7.4V (maximum voltage up to 8.4V)
  or MZW124-02 AC adapter (6V- 2A / For Japan)

Aluminum impact resistant front and rear bumpers.

Steering plate set. 5 kinds of toe angles can be selected for wider setup range.

Recommended Stand for working on the damper. The magnet plate on the front will help preventing to lost screws.

■ Input voltage USB Type-C 5-12V (Power supply with output 3A or more compatible with Quick Charge 2.0 / 3.0 and Power Delivery is recommended)
* Please purchase the charging adapter separately.
■ Body size 120x92x34 (mm)
■ Weight 195g
■ Number of charging 1-4
■ Compatible batteries NiMH, NiZn, Li-Ion, LiHV, LiFe AAA type (AAA), AA type (AA), 10440, 10500, 12500 , 13500, 13650, 14500, 14650, 16650, 17650, 17670, 18650, 18700, 20650, 20700, 21700, 22650, 26650, 26700 * Batteries longer than 70mm cannot be used

Internal resistance: 0.0011Ω
Continuous maximum current: 60A
Instantaneous maximum current: 80A
Maximum KV value (2S): 13.5T 3200KV
Driving mode: Forward / brake / forward / brake / reverse
Input voltage: 7.2V-11.1V
Compatible motor type: Sensor & Sensorless
BEC output: 6V / 2A
size (mm): 37.5 x 30.8 x 18.7
Weight (g): Approximately 80

■Length: 612mm
■Width: 130mm
■Height: 1,135mm
■Weight: 1,050g
■Sail Area: 21.85dm2

■Length 570mm
■Width 450mm
■Height 281mm
■Weight 4,990g
■Wheelbase 360mm
■Tread F:339mm R:343mm
■Tires （F & R） φ164×104mm
■Gear Ratio 25.7/19.8/15.6:1
■Engine KE25SP2 with recoil starter

<Readyset Contents>
●Pre-assembled chassis with pre-set control linkages
●Pre-cut and painted body complete with decals applied
●2.4GHz Syncro KT-231P+ transmitter
●L shaped hex wrench (1.5mm, 2.0mm, 2.5mm, 3.0mm)
●Cross wrench (large)
●17mm wheel wrench

<Required for Operation>
●AA-size batteries x 4 for transmitter
●AA-size batteries x 4 for receiver
●Glow fuel for models
●Fuel bottle
●Plug heater

Spare tires & white wheels for the Mad Van VE. By using with EZT001S, FA535-S20, FA535-76 and 1-S14018H, wheels can be equipped on the Rage 2.0 chassis(34411).

Roll damper for R246-2351 MML Motor Mount. Oil damper is sold separately. Compatible dampers: R246-1360, R246-1221, and MZW432.

Aluminum MM2 type motor mount.
Features:
- Precision lightweight design achieves less than 7g in weight while maintaining sufficient rigidity
- Compatible with R246-1362 roll damper as well as MZ217 standard plastic one

Roll damper for R246-1361 and MZ217 MM2 Motor Mount.
Features:
- Blue anodized precision machined aluminum with shiny finished edges
- Recommended using with R246-1360 oil damper
- Can be assembled in L, LL and 3L wheelbases

Mini Z Body Shell

■ Number of channels 4 channels
■ Weight 398g
■ Power supply 4 AA alkaline batteries
■ Compatible model Car & boat
■ RF range 2.405-2.475GHz
■ 2.4GHz system FHS (MINI-Z) / FHSS 1Way (KR-331) / FHSS 2Way (KR-431T)
■ Low voltage warning 3.7V or less
■ Steering range 66 ° (45 ° left and right)
■ Throttle range 45 ° (front and rear angle 30 °)
■ Certification CE0678.FCC

Spare air cleaner for the KE21SP/KE25SP engine

Spare parts for the MAD CRUSHER / FO-XX. Included Front Housing parts and screws as 1 set. Not compatible with MA002, MA004F and MA331.

Spare parts for the FANTOM EP 4WD

Spare parts for the MP10T

Mercedes AMG GT3 white body for the MINI-Z MR-03 series

Yellow colored Javelin roll cage body.

■Length　490mm
■Width　307mm
■Height　180mm
■Ground Clearance　28mm
■Wheelbase　325mm (4 settings available by changing rear hub collar position)
■Tread (F/R)　254mm (2 front settings and 3 rear settings available by changing bushes)
■Tire (F/R)　φ116 x 44mm
■Gear Ratio　11.7:1
■Weight　3,370g approx.
■Engine　KE21SP (recoil starter installed/rear exhaust)

■Length 469mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.56：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

Stunning red anodized aluminum link rods for better appearance. For 120mm wheelbase.

Size: 35.8x51.2mm
Shaft size: 3.175x17mm
Weight: Approximately 180g
Number of turns: 21.5T
Operating voltage: Max 12.8V (2 to 3S LiPo compatible)
kv value: 1950 (rpm / V)
Maximum rotation speed (at 7.4V) : 14430rpm
Maximum current: 30A
Maximum output: 260W
Maximum efficiency: 91%

■Length 660mm ■Width 160mm ■Height 325mm ■Weight 1,500g approx. ■Motor 540-class G24 motor with water-cooling jacket ■Screw D31 x P1.4 (polycarbonate) ■Charging Time 8 hours approx. 16km/h approx. ■Operation time 7 min approx

■Length 660mm ■Width 160mm ■Height 325mm ■Weight 1,500g approx. ■Motor 540-class G24 motor with water-cooling jacket ■Screw D31 x P1.4 (polycarbonate) ■Charging Time 8 hours approx. 16km/h approx. ■Operation time 7 min approx.

Spare parts for the Ultima

■Length: 945mm
■Width: 230mm
■Weight: 2,350g
■Motor: KYOSHO SPEED HOUSE TORX M6 water-cooled brushless motor (40x68mm, KV1250)
■Battery: 2 x 3 cell 11.1V-3600-4000mAh LiPo battery (Super Plug specification, sold separately)
■R/C System: Perfex KT-231P+
■Propeller: D40×P1.4（3-blade）
■ESC : KYOSHO SPEED HOUSE KA120-91WC 120A water-cooled, waterproof brushless ESC

■Length: 900mm
■Width: 187mm
■Height: 140mm
■Weight: 1,780g (when 14.8V-4000mAh installed)
■Motor: Pre-installed KYOSHO SPEED HOUSE TORX M4 Brushless water-cooled motor (40x68mm, KV2000)
■Battery: 4 cell 14.8V 3600-4000mAh LiPO (Super Plug specification, sold separately)
■Propeller: Carbon reinforced nylon D40 x P1.4 (3-blade)
■ESC: Pre-installed KYOSHO SPEED HOUSE 120A KA120-91WC water-cooled, waterproof brushless ESC
■Servo: KS-4031-06W

Spare parts for the TURBO OPTIMA.  
Optional parts for the OPTIMA and JAVELIN.

Spare parts for Javelin. Compatible with the Optima to use the Javelin roll cage body.

Spare linkage set for the Inferno MP10T. Compatible with the MP9 / MP10.

■Length  575mm
■Width  428mm
■Wheelbase 381-386mm
■Tread（F/R） 353mm／353mm
■Tires（F/R） For stadium track(not included)
■Gear Ratio 16.3:1
■Weight  3,870g approx.
■Engine .21 ～ .28 classes(not included)
■Transmitter 2ch or more 2 servo(not included)

Body Shell for Mini Z

Body shell for Mini Z

Spare parts for the Mini-Z AWD

CNC machined aluminum hub carrier for the MP10. 
Increases durability and rigitity. Includes bushings for bearing protection.

Aluminum heat sink for the motor. Keeps motor temperture low efficiently.