●Scale approx. 1/28
●Product size: L164 x D73 x H45 (mm) ● Body
weight: approx . Mode: 7km/h / Racing mode: 10km/h ●Operable distance: approx. 30m ●Frequency: 2.4GHz (12 units can run simultaneously) ●Continuous running time: approx. 60 minutes (when using new alkaline batteries) ●Target age: 6 years old that's all

KIT CONTENTS

Spare parts for MP10
Front and rear lower suspension arms have been significantly reinforced for greater strength and also designed so they don’t catch dirt for easier cleaning and maintenance. The new arms are also substantially thicker around the large diameter φ4.5mm hinge pins to make the arms even more resilient.

Spare parts for MP10

Spare parts for MP10

Technical data

Spare parts for MP10
Based on the suspension geometry of the MP9 TKI4 shock stay, the number of shock and upper arm mounting holes has been optimized. In addition, the reinforced rear shock stay delivers increased strength and prevents dirt catching.

Spare parts for MP10
Based on the suspension geometry of the MP9 TKI4 shock stay, the number of shock and upper arm mounting holes has been optimized. In addition, the reinforced rear shock stay delivers increased strength and prevents dirt catching.

Spare parts for MP10
Newly designed upper plate delivers improved front traction and steering performance.

Spare parts for MP10
At first glance the radio plate looks similar to the MP9 TKI4, but the MP10 design features a revised servo position and increased strength with 3.0mm thickness, increased from 2.5mm.

Can fit in Inferno Neo

Optional parts for the INFERNO MP9 Series.
Hard type wheel of existing IFH006 Dish Wheel.
It tends to have a stable running when exiting corner and acceleration.
You can select the wheel depending on racing track and you wish.

■Scale: Approximately 1/28 scale
■Total length: 130mm
■Total width: 70mm
■Total height: 35mm
■Weight: Approximately 110g (excluding AA alkaline batteries)
■Maximum speed: Training mode: 7km/h Racing mode: 10km/h
■Operating distance: Approximately 30m
■Frequency: 2.4GHz (12 units can run simultaneously)
■Continuous running time: Approximately 60 minutes (when using new alkaline batteries)
■Recommended age: 6 years old and above

<Set contents>
● First Minute main unit
● 2.4GHz controller with stopwatch
● Mini pylon (6 pieces)
● Sticker
● Trim adjuster
● Battery holder

<Required to run>
Main unit: 2 AA alkaline batteries
Transmitter: 2 AA alkaline batteries

Can fit in Inferno Neo

■Length 397mm
■Width 250mm
■Height 135mm
■Wheelbase 273mm
■Tread（F／R） 212mm / 208mm
■Weight  approx 1620g (with 7.2V4000 LiPo）
■Tires（F／R） φ82×30mm / φ82×36mm
■Motor 540 class size (sold separately)
■Gear ratio 8.28：1

<Kit Contents>
●Chassis
●Tire
●Wheel
●Clear body＆underbody
●Decals
●Hexagon wrench
●Cross wrench
●Shock wrench
●Grease
●#200Shock oil
●Ball Differential Grease

＜Required for Operation＞
●2 channel R/C system
●Servo
servo size：L41xW21xH38mm 
●540Motor
●ESC
ESC size：L40xW42xH29.5mm
●Battery for chassis
Battery size:L140xW50xH25mm
●Batteries for transmitter
●Charger for battery
●Paint for body

2 light halogen LED and 2 light red LED light set. Connects to the Rx open slot and includes extention cords for additional light sets.

●Scale: Approximately 1/28 scale
●Product size：L181 x H46 x D71（mm）
●Product weight：109g (approx.)
●Package size：W215 × H225 × D115（mm）
●Package weight：433g (approx.)
●Maximum speed: Training mode: 7km/h Racing mode: 10km/h
●Operation distance: approx. 30m
●Frequency: 2.4GHz (12 vehicles can run simultaneously)
●Continuous running time: Approximately 60 minutes (when using new alkaline batteries)
●Target age: 6 years old or older

<Kit Content>
●Main unit
●2.4GHz controller with stopwatch
●Mini pylons (6 pieces)
●Trim adjuster
●Battery holder

<Required to run>
●AAA-size alkaline batteries x 2 for chassis (sold separately)
●AAA-size alkaline batteries x 2 for transmitter (sold separately)

■Length 500mm
■Width 211mm(Body width * excluding mirror)
■Height 130mm
■Wheelbase 274mm
■Tread (F/R) 167mm
■Tires (F/R) φ64×27.7mm
■Gear Ratio 6.54：1
■Weight  1650g (approx.)
■R/C system Syncro KT-231P+
■Motor G14L

<Kit Contents>
●Completed chassis with R/C radio installed
●Factory assembled body complete with color scheme
●Syncro KT-231P+ transmitter
●Hexagonal wrench
●Spanner
●Setting change parts

<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tools

Compared to conventional 3pc clutch shoes, durability is greatly improved More accurate for clutch on & off by material change. ※Option parts for INFERNO series.

Φ0.95 clutch springs for the IFW636

Φ0.9 clutch springs for the IFW636

Option part for the INFERNO MP10, MP10 TKI2, and MP10T.
Lower weight than the existing aluminum clutch shoes, but stronger acceleration with the refined engagement surface.
Two types of clutch springs, Φ0.9 and Φ0.95 are available for a wider range of clutch settings.

Spare parts for the Fazer Mk2 Touring Car

2.2 inch rear wheel with offset suitable for vintage buggy chassis.
Used when using 2.2 inch tires.
38mm width.

<Compatible chassis> *2.2 inch tires are required for each vehicle.
No.30617 Optima
No.30618 Javelin
No.30619 Turbo Optima
No.30622 Optima Mid
No.30625 Ultima

Optional parts for INFERNO MP10 series and MP9 series. Light weight 47T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, acceleration will be quicker and smoother. Smoother deceleration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires to use with IF403B Diff case set.

New light weight 46T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.

New light weight 45T spur gear for use with smaller diff for the center(Same as front and rear diff). By using the smaller diff, accelaration will be quicker and smoother. Smoother deaccelaration can also be achieved. This spur gear is design to fit the smaller diff case replacing the stock diff housing which is larger. Requires the use of IF403B Diff case set. Compatible with MP10/9 series.

Optional parts for the INFERNO MP10.

※It is not possible to drive with auto scale alone. In addition, some bodies cannot be mounted depending on the chassis.
※The separately sold LED light unit set (No.MZW429R) cannot be installed on the McLaren Senna GTR.

●Body size: φ110 (including rotor) x H89 (mm)
●"Doraemon" body size: W48.8 x H58 x D39.3 (without rotor) (mm)
●Body weight: 19g
●Transmitter size: W116 x H89 x D36 (mm)
Package size: W185 x H245 x D118 (mm)
Target age: 10 years old and over

● "Flying Doraemon" body
● Transmitter
● Instruction manual
● USB cable
● Spare parts Rotor (1 set)
● Paper display stand

Spare parts for FAZER MAD VAN series and RAGE 2.0

Spare parts for the FANTOM EP 4WD

＜適合車種＞
■MINI-Z MR-03W-MM
＜仕　　　様＞
■Wheel Base：LL（98mm）
■Wheel Off Set：F：N+1.5 / R：W+1.5
■Wheel Width：F：8.5mm / R：11mm

＜適合車種＞
■MINI-Z MR-03W-MM
＜仕　　　様＞
■Wheel Base：LL（98mm）
■Wheel Off Set：F：N+1.5 / R：W+1.5
■Wheel Width：F：8.5mm / R：11mm

Optional parts for the INFERNO MP10/MP9e Evo. 
New setting weights by 10g and 20g which can be installed the main chassis. 
Can be adjusted the weights in 10g/20g/30g/40g by weights combination. 
Fixing by screws and nylon nut which prevents falling off when driving.

Use for front tires on MINI-Z Racer and MINI-Z AWD. Reduces sticking on urethane surfaces for smooth running characteristics.

Spare parts for MP10

Spare parts for MP10

Spare parts for MP10
High strength and precision construction of molded rear hub delivers improved controllability and better handling char

Spare parts for MP10

※Old Parts #：IF346-05 / IF346-05B

BATTERY AND CHARGER SOLD SEPERATELY

■Length 383mm(Including body)
■Width 323mm(Including body)
■Height 200mm(Including body)
■Wheelbase 274mm
■Tread (F/R) 250mm
■Tires (F/R) φ110×70mm
■Gear Ratio 11.69:1
■Motor G14L
■Weight 2,050g (approx.)(When using 7.2V3600 NiMH)

<Readyset Contents>
●Factory assembled chassis with built in R/C unit
●Factory finished body with decals applied
●Syncro KT–231P+ transmitter
●Hex wrench
●Integrated spanner
●Setting change parts

<Required for Operation>
●4 x AA batteries for transmitter
●Battery for chassis (recommended: 7.2V Ni-MH battery)
●Charger for battery for chassis
●Tools

■Length　163mm
■Width　105mm
■Height　46mm
■Wheelbase　115mm
■Tread（Ｆ/Ｒ）　89mm/89mm
■Tires（Ｆ/Ｒ） φ37×13.5mm／φ37×18.5mm
■Weight　200g approx.
■Motor　SPEED HOUSE XSPEED 85 (8500KV)

<Set Contents>
●Factory assembled MB-010VE chassis installed with XSPEED VE brushless motor.
●Pinion gears x 3 (11T, 13T, 15T)
●Spur gears x 2 (33T, 35T)
●Wheel wrench
●Pinion gear tool
●Pairing stick
●Spare wheel nuts

<Required for Operation>
●KT531P transmitter
●Paint for body
●4 x AAA alkaline or Ni-MH batteries for chassis
●4 x AAA alkaline batteries for transmitter (EX-5UR ASF requires 8 x AA alkaline batteries)