■Scale: Approximately 1/28 scale
■Total length: 130mm
■Total width: 70mm
■Total height: 35mm
■Weight: Approximately 110g (excluding AA alkaline batteries)
■Maximum speed: Training mode: 7km/h Racing mode: 10km/h
■Operating distance: Approximately 30m
■Frequency: 2.4GHz (12 units can run simultaneously)
■Continuous running time: Approximately 60 minutes (when using new alkaline batteries)
■Recommended age: 6 years old and above

<Set contents>
● First Minute main unit
● 2.4GHz controller with stopwatch
● Mini pylon (6 pieces)
● Sticker
● Trim adjuster
● Battery holder

<Required to run>
Main unit: 2 AA alkaline batteries
Transmitter: 2 AA alkaline batteries

■Scale: Approximately 1/28 scale
■Total length: 130mm
■Total width: 70mm
■Total height: 35mm
■Weight: Approximately 110g (excluding AA alkaline batteries)
■Maximum speed: Training mode: 7km/h Racing mode: 10km/h
■Operating distance: Approximately 30m
■Frequency: 2.4GHz (12 units can run simultaneously)
■Continuous running time: Approximately 60 minutes (when using new alkaline batteries)
■Recommended age: 6 years old and above

<Set contents>
● First Minute main unit
● 2.4GHz controller with stopwatch
● Mini pylon (6 pieces)
● Sticker
● Trim adjuster
● Battery holder

<Required to run>
Main unit: 2 AA alkaline batteries
Transmitter: 2 AA alkaline batteries

■Length 660mm
■Width 310mm
■Height 180mm
■Wheelbase 360mm
■Tread (F/R) 262mm／265mm
■Tire (F/R)  Φ97mm ×40mm
■Gear Ratio 1st gear /10.14:1　2nd gear /7.49:1
■Weight 3,660g（approx. ）
■Engine　KE25SP2
■Transmitter　Syncro KT-331P

<Kit Content>
●Pre-assembled chassis installed with 2-ch, 2-servo R/C system and pre-set control linkages
●Pre-painted factory assembled body with decals applied
●Installed KE25SP2 rear exhaust engine
●Installed polished tuned muffler
●Syncro KT-331P transmitter
●Hex wrenches: 1.5, 2.0, 2.5, 3.0mm
●Cross wrench (large)
●17mm wheel wrench
●Nylon strap (for air cleaner)
●Break in ring
●Bind code

<Require to run>
●8 x AA batteries for transmitter (4) and receiver (4)
●Fuel
●Engine starting tools (fuel bottle, plug heater)

0.5mm-thick FRP rear suspension plate set. Contains soft, medium and hard plates. Softer than the MZW409, which is 0.6mm thick.

Carbon rear suspension plate for MM/LM/MM2. Contains 3 pcs of soft plates.

Aluminum motor mount for the MR-03LM.
High precision machined product made in Japan.
Highly balanced left-right weight distribution contributes to superior traction.
The design supports the LL (98mm) wheelbase as well.  Works best with the MZW310 Inner Tube Roll Shock Set.

Optional parts for MR-04.

Optional parts for MR-04 EVO2

Spare parts for MR-04 EVO2

Spare parts for MR-04 EVO2

Optional parts for the INFERNO MP9/MP10. Reinforced Servo Saver than existing one, increases the hardness and steering response.

Spare parts for INFERNO MP10e Readyset

■Length 469mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.56：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

■Length 469mm
■Width 307mm
■Height 189mm
■Wheelbase 325.5mm
■Tread (F/R) 258mm／261mm
■Tire (F/R) φ116×44mm／φ116×44mm
■Gear Ratio 11.56：1
■Weight 3,400g (approx.)
■Engine KE21SP
■Transmitter 2.4GHz Syncro KT-231P+

<Readyset Contents>
●Factory assembled chassis complete with control linkages
●Finished body complete with printed color scheme
●2.4GHz Syncro KT-231P+ transmitter
●1.5、2.0、2.5、3.0mm L shaped hex wrenches
●Cross wrench
●17mm wheel wrench

■Length　490mm
■Width　307mm
■Height　180mm
■Ground Clearance　28mm
■Wheelbase　325mm (4 settings available by changing rear hub collar position)
■Tread (F/R)　254mm (2 front settings and 3 rear settings available by changing bushes)
■Tire (F/R)　φ116 x 44mm
■Gear Ratio　11.7:1
■Weight　3,370g approx.
■Engine　KE21SP (recoil starter installed/rear exhaust)

<Kit Content>
●Factory assembled chassis installed with R/C system
●Printed pre-cut body complete with coloring
●Pre-installed KE21SP engine with rear exhaust
●Syncro KT-331P transmitter
●1.5, 2.0, 2.5mm Hexagonal wrench
●Cross wrench (small)
●17mm Wheel wrench

<Require to run>
●AAA x 8 alkaline batteries for transmitter
●Fuel
●Starting tools (Fuel bottle, Plug heater)

■Operating Voltage: 4.8-6.0V
■Size：L35.9mm W15.1mm H28.6mm
■Speed：0.13sec/60°
■Torque：4.5kgf・cm
■Weight：30g
■Led Wire：150mm
■Serration：25 / for FUTABA・KYOSHO

・Servo x1
・Horn A x1
・Horn B x1
・Horn C x1
・3ｘ5ｘ1mm Spacer x1
・Eyeletｘ4
・Screw 2.3x12mm x4
・Screw 2.6ｘ6ｍｍｘ1
・Grommetｘ4

Machined aluminum upper sus arm realizes direct spring effect.

■Length　490mm
■Width 　307mm
■Height 　180mm
■Ground clearance　28mm
■Wheelbase　325mm 
■Tread（Ｆ／Ｒ）　254mm
■Tires（Ｆ／Ｒ）　sold separately
■Gear Ratio　11.7：1
■Weight　3,360g(approx.)
■Engine　21Class (sold separately)

＜Kit Contents＞
●Unassembled chassis kit
●Special wheels
●Wing
●Special clear body
●Window mask seal
●Logo decals
●Fuel tube
●Linkage parts
●Clutch parts
●Air cleaner
●Ring gear grease
●1.5, 2.0, 2.5mm Hexagonal wrench
●Cross wrench 
●Wheel wrench

＜Required for Operation＞
●2-channel 2-servo R/C system for cars
●Compatible batteries for R/C system
●21 engine
●Muffler
●Tires w/foam inserts for 1/8 buggy
●Starter box
●Plug heater
●Fuel
●Fuel bottle
●Oil for air cleaner
●Shock oil
●Diff oil
●Paint for car body
●Tools

■Length　375mm
■Width　200mm
■Wheelbase　258mm
■Tread (F/R)　176mm
■Tire(F/R)　φ66×25mm
■Gear Ratio　7.47 / 5.44：1
■Weight　1,800g (approx.)
■Engine KE15SP with recoil starter
■Max Speed 64Km(approx.)

<Kit Contents>
●chassis kit
●FAT701M TC Tire (M)＆Inner sponge、VZH003BK  Wheel（not glued）
●Pre-mounted KE15SP engine with recoil starter
●Setting change parts
●1.5mm/2.0mm/2.5mm/5.0mm Hex wrench
●Cross wrench
●3/4/5/5.5/7/8mm Spanner

<Required to run>
●2ch R/C car transmitter
●Body
●Servos x 2
●4 x AA sized alkaline batteries for receiver and Battery Holder or Battery
●4 x AA sized alkaline batteries for transmitter
●Switch
●Silicon oil for Shock
●Silicon oil for diff
●Grease
●GP Starting Tool Set
●Fuel Bottle
●Glow Fuel
●Tool

Option Parts for ULTIMA RB6

Machined aluminum wheel hub. Increased durability.

Spare parts for MAD WAGON

Option parts for the Fazer Mk2. CNC machined aluminum front hubs allow precise and linerar steering response and smooth suspensionmovement. Allows camber angle adjustments.

Option parts for the Fazer Mk2. CNC machined aluminum rear hubs allow smoother suspension movement. Allows 2 camber angle adjustments.

■Size
Overall：W360 X L560 X H550(mm)
Inner dimensions of one of the inner boxes：W325 X L505 X H160(mm)

■Carrying Bag for1/8
■Considerable materials for heavy duty use.
■Chic black color.
■Plastic cardboard for shelves
■Outside pocket equipped.
■Equipped with multipurpose slit and travel carrier.

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Spare parts for MAD WAGON

Option Parts for INFERNO GT2 Type-R.

Spare Parts for SCORPION 2014

High RPM and torque .21 size big block engine. Easy to tune with recoil starter.

*This product does not come with a break-in ring.When you break in, please use the accessories that came with the Readyset when you purchased it.

Gyro unit for MINI-Z readyset. Compatible with blue board RC units, or green board RC units with a blue marking on the gyro connector.

Correspondence table

Complete body set for the Inferno GT2. Licensed 2020 Mercedes AMG GT3 body. Wheelbase : 360mm / Body Dimensions : 661 x 310 x 164mm(With rear wing)

Aluminum big bore shocks for Rage 2.0. Threaded large capacity shock bodies.

<Required for Operation>

EP Version
●4 channel, 4 servo R/C system for airplanes (standard servo x 4)
●Batteries for transmitter
●100mm Y extension cord x 1 for aileron servo
●200mm extension cord x 2 for aileron servo
●Propeller
●Out Runner BL motor for 40-50 class
●ESC
●Li-Po battery
●Charger for Li-Po battery

GP Version
●4 channel, 5 servo R/C system for airplanes (standard servo x 5)
●Batteries for transmitter
●100mm Y extension cord x 1 for aileron servo
●200mm extension cord x 2 for aileron servo
●Propeller
●2 cycle 40-46 engine for airplanes
●Starting tools (plug heater, starter, starter battery, charger)
●Glow fuel for airplanes

■Length: 998mm
■Width: 226mm
■Height: 1,850mm
■Weight: 3,100g
■R/C System: Syncro KT-431S, 2.4GHz, FHSS
■Sail Area: 39dm2
■Servo: Sail KS9071-20SW（waterproof）/　Rudder KS4031-06W

＜Readyset Contents＞
●Pre-colored fully assembled hull
●Syncro KT-431S 2.4GHz R/C system installed
●Folding wood boat stand
●Mast Assy
●Decal for Sail
●Painted Rudder, Keel & Ballast

＜Required for operation ＞
●8 x AA sized batteies for transmitter/receiver (4 for transmitter, 4 for receiver)

Option parts for Hang-on Racer

Option parts for Hang-on Racer

Mini steering servo for the Hang On Racer. Bolt on ready. 150mm wire with JR type no flange connector housing. Screw and aluminum collar included.

Option parts for Hang-on Racer

Rocky terrain for the MINI-Z 4x4. A set of 5 pieces of 480 x 480 x 103mm terrain. Making a square with four pieces and putting the 5th one on the center of the square will make a 960 x 960 x 156mm terrain, and you can enjoy wide variety of terrain by rotating each piece. Even larger terrain can be made using multiple sets.

Spare parts for Optima Mid

Spare parts for OPTIMA MID

USA-1 clear body set with plastic parts. Compatible with 8th scale monster trucks. Includes chrome body parts, decals and masking sheet. Light buckets are compatible with LED optional headlights(97054 / headlights x 8 , Tail lights x 2 and fog lamp x 5). Wheelbase : 360mm / Body dimension : 539 x 206 x 142mm(Without side mirrors & fog lamps)

[Contents]
・ Motor checker body
・ Power cable with super plug ・
O-ring for fixing motor x2 (1 is spare)
・ Rotation adapter x2 (1 is spare)
・ Wiring cable with alligator clip for brush motor
・ Instruction instructions book

[Items that need to be purchased separately] -Battery
motor or brushless motor for minutes (measurement target)
-Battery with super plug from 5.5V to 7.4V (maximum voltage up to 8.4V)
  or MZW124-02 AC adapter (6V- 2A / For Japan)

Steering plate set. 5 kinds of toe angles can be selected for wider setup range.

Recommended Stand for working on the damper. The magnet plate on the front will help preventing to lost screws.

■ Input voltage USB Type-C 5-12V (Power supply with output 3A or more compatible with Quick Charge 2.0 / 3.0 and Power Delivery is recommended)
* Please purchase the charging adapter separately.
■ Body size 120x92x34 (mm)
■ Weight 195g
■ Number of charging 1-4
■ Compatible batteries NiMH, NiZn, Li-Ion, LiHV, LiFe AAA type (AAA), AA type (AA), 10440, 10500, 12500 , 13500, 13650, 14500, 14650, 16650, 17650, 17670, 18650, 18700, 20650, 20700, 21700, 22650, 26650, 26700 * Batteries longer than 70mm cannot be used

■Length: 612mm
■Width: 130mm
■Height: 1,135mm
■Weight: 1,050g
■Sail Area: 21.85dm2

■Length 570mm
■Width 450mm
■Height 281mm
■Weight 4,990g
■Wheelbase 360mm
■Tread F:339mm R:343mm
■Tires （F & R） φ164×104mm
■Gear Ratio 25.7/19.8/15.6:1
■Engine KE25SP2 with recoil starter

<Readyset Contents>
●Pre-assembled chassis with pre-set control linkages
●Pre-cut and painted body complete with decals applied
●2.4GHz Syncro KT-231P+ transmitter
●L shaped hex wrench (1.5mm, 2.0mm, 2.5mm, 3.0mm)
●Cross wrench (large)
●17mm wheel wrench

<Required for Operation>
●AA-size batteries x 4 for transmitter
●AA-size batteries x 4 for receiver
●Glow fuel for models
●Fuel bottle
●Plug heater

Preglued USA-1 tire and wheel set. Includes 2pcs

Can be mounted on the FAZER Mk2 series FZ02L-BT / FZ02L VE-BT chassis.
Body accessory parts with plated finish improve scale realism for body shell, protector parts protect the roof when turn over, polycarbonate rear spoiler, decals and masking sheets used for the ready set. Comes with decoration decals for customized body shell you wish. The LED light unit series (#97054) sold separately can be installed in the light buckets.
Finished body size: Approximately 378x154x135mm (excluding mirrors)

INFERNO MP10 TKI2 Spare parts

Spare tires & white wheels for the Mad Van VE. By using with EZT001S, FA535-S20, FA535-76 and 1-S14018H, wheels can be equipped on the Rage 2.0 chassis(34411).

Speed controller for 60A waterproof sensorless brushless motor. Cooling fan helps to protect the ESC from overheat and supply stable power. Input voltage : 2-3S LiPo (7.4-11.1V) or 6-9S NiMH battery (7.2-10.8V). Size : 48.5x38x32mm (including cooling fan) / Continuous maximum current : 60A / Peak current : 390A / Weight : 90g / Bec output : 6V/3A

Sensorless brushless motor 4000kv (shaft diameter : 3.175mm) for 2S LiPo. The main body has a dustproof structure to avoid maintenance. Suitable for 1/10 On and Off-road cars. Weight : 205g

■Length　1300mm
■Width　1600mm
■Weight　EP/2,550g (approx.), GP/2,450g (approx.)
■Motor　600-1000W BL Motor (sold separately)
■Engine　2 Cycle 40-46 class engine (sold separately)
■Battery (EP)　14.8V-4,000-5,000mAh Li-Po battery (sold separately)
■Main Wing Area　 44dm2
■Wing Loading　55.7-55.9g/dm2
■Airfoil 　Original semi-symmetrical
■Propeller size　D11 x P7-D12 x P8 (sold separately)
■Tire size　Nose 60mm / Main 60mm
■Dihedral　2.5°
■Side Thrust　2°
■R/C system (EP)　4ch, 4 servo, 1 ESC (sold separately)
■R/C system (GP)　4ch, 5 servo (sold separately)

■Length: 1,600mm
■Width: 1,800mm
■Weight : (EP) 3,900g　(GP) 3,700g
■Motor(EP): 800-1200W class backplate mounted outrunner brushless (sold separately)
■Engine (GP): 2-cycle 60-65 class (sold separately)
■Battery (EP): 14.8V 5,000ｍAh Li-Po (sold separately)
■Wing Area: 60.6dm2
■Wing Load : 61.0-64.3g/dm2
■Wing Type : Original semi-symmetrical
■Propeller : D12xP6-D14xP8 (sold separately)

■Length: 1,600mm
■Width: 1,800mm
■Weight : (EP) 3,900g　(GP) 3,700g
■Motor(EP): 800-1200W class backplate mounted outrunner brushless (sold separately)
■Engine (GP): 2-cycle 60-65 class (sold separately)
■Battery (EP): 14.8V 5,000ｍAh Li-Po (sold separately)
■Wing Area: 60.6dm2
■Wing Load : 61.0-64.3g/dm2
■Wing Type : Original semi-symmetrical
■Propeller : D12xP6-D14xP8 (sold separately)

Spare 3pcs flywheel for the Inferno NEO / NEO ST / GT2

Carbon center bulk plate for the MP10. Carbon allows lighter weight without sacrificing durability.

Roll damper for R246-2351 MML Motor Mount. Oil damper is sold separately. Compatible dampers: R246-1360, R246-1221, and MZW432.

Aluminum MM2 type motor mount.
Features:
- Precision lightweight design achieves less than 7g in weight while maintaining sufficient rigidity
- Compatible with R246-1362 roll damper as well as MZ217 standard plastic one