There are 2561 products.
*The Auto Scale body alone is not drivable. Additionally, some bodies may not fit certain chassis.
*The separately sold LED light unit set (No.MZW429R) can be installed on the Toyota Corolla Levin AE86.
*The Auto Scale body alone is not drivable. Additionally, some bodies may not fit certain chassis.
*The separately sold LED light unit set (No.MZW429R) can be installed on the Toyota Corolla Levin AE86.
Cell chemistry - LiPo HV
C-rate - 120C/60C
Length - 139.0mm
Width - 47.0mm
Height - 17.5mm
Weight - 215g (+/-4%)
Connectors - 5mm
Homologated - ROAR, EFRA, BRCA
* This product is a spare body set and cannot be run. To enjoy driving as an RC model, please purchase a ready set.
Aluminum front hub carrier. Provides increased rigidity and better appearance.
Light unit compatible with the I.C.S connector of the RC units of ASF and MHS/ASF systems. Tail lights are brighter while braking.
Absorbs difference in front and rear tire rotation even through small corners to realize ultra-smooth cornering. Suitable for technical courses where quick handling is required.
Spring set adjusts hardness of suspension. Includes 3 hardness types. *For MA-020S rear.
Weight-90g
Nominal voltage-7.4V
C-rate-RX-only
Dimensions-84x30x17mm
Capacity-2500
Balancing connector-XHR 3-pole
■Length 490mm
■Width 307mm
■Height 180mm
■Wheelbase 325mm (can be changed with rear hub collar)
■Tread (F/R) 254mm
■Tires (F/R) φ116×44mm
■Weight 3,370g (approx..)
■Motor KYOSHO SPEED HOUSE TORX 8 Brushless Motor
<Readyset Contents>
●Completed chassis with R/C radio installed
●Pre-cut and colored printed body
●KYOSHO SPEED HOUSE brushless motor & ESC installed
●Syncro KT-331P transmitter
●1.5, 2.0, 2.5, 3.0mm L type hexagonal wrench
●Cross wrench (large)
●17mm wheel wrench
<Required for Operation>
●4 x AA batteries for transmitter
●2 x batteries for chassis
●Charger for batteries for chassis
●Regulated power supply
■Length 162.0mm
■Width 73.0mm
■Height 49.0mm
■Wheelbase 90.0mm（M）
■Tread F : 61.5mm R : 59.0mm
■Chassis MA-020-N
■Front Wheel Offset Narrow +2.5mm
■Rear Wheel Offset Wide ±0.0mm
■R/C System Syncro KT-531P
<Ready set contents>
● R / C unit built-in complete chassis
● Painted and marked complete body
● Ｓyncro KT-531P transmitter
● Mini pylon
● Pinion gear (15T, 17T, 19T, 21T)
● Spur gear (27T, 29T, 31T)
● Spare nut
● Wheel wrench
● Pinion removal tool
＜ Required for Operation ＞
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 for transmitter
※It is not possible to drive with auto scale alone. In addition, some bodies cannot be mounted depending on the chassis.
※The separately sold LED light unit set (No.MZW429R) cannot be installed on the Audi R8 LMS Phoenix Racing NBR 2010 #98.
Machined aluminum steering blocks. Available in 0.5°, 1.5°, and 2.5° camber angles, based on the standard 0°. Similar to the MZW702, they feature a realistic design that allows adjustment of the upper arm mounting position and kingpin tilt, just like full-scale vehicles. When combined with the MZW702, fine-tuned adjustments can be made from 0°to 3°in 0.5°increments.
FAZER Optional parts for Mk2 FZ02-R.
Setting parts for adjusting grip in response to vehicle setup and road surface conditions. Contains 2 pieces of each of 3 types: Soft, Medium (equivalent to standard), and Hard.
Coil inner diameter: 16.5mm, overall coil length: 44mm, wire diameter: 1.1mm.
※You need to purchase two to make one unit.
Contents
Soft (pink / total 9 rolls) ×2
Medium (yellow / total 8 rolls) ×2
Hard (blue / total 7 rolls) ×2
Optional parts for FAZER FZ02-R.
※When used with the FZ02L-BT series, please also use Button Screws (M4x22) (Hex/5 pcs) part No. 1-S14022H.
Designed for 1/10 RWD drift cars. Optional parts for the FAZER D2 drift car. The standard servo horn is made of resin, but upgrading to a CNC-machined aluminum version significantly enhances steering response and holding strength. Additionally, the adjustable design allows fine-tuning of the steering feel by adjusting the arm length from 17mm to 21mm. FAW310 is compatible with Kyosho and Futaba, while FAW311 is compatible with Sanwa and KO.
Size：40.5×26.5×21mm(Low Profile type）
Weight：42.1g
Power Supply：6.0～7.4V
Speed：0.08sec/60°(7.4V) 0.09sec/60°(6.0V)
Torque：8.2Kg・cm(7.4V) ７.0Kg・cm(6.0V)
<Contents>
●Servo×1
●Grommet
●Horn set screw
●Instruction Manual
※This product is a spare body set and cannot be run. To enjoy driving as an RC model, please purchase a ready set.
※The separately sold LED light unit set (No.MZW429R) can be installed on the NISSAN SKYLINE GT-R R32 V-SPECⅡ.
■Length 181.0mm
■Width 78.0mm
■Height 40.0mm
■Wheelbase 102.0mm （3L）
■Tread F : 68.5mm R : 66.0mm
■Chassis RWD（MR-03）
■Motor Mount LM
■Front Wheel Offset Narrow +2.7mm
■Front Wheel Offset Wide +0.8mm
■R/C System Syncro KT-531P
<Readyset Contents>
●Factory assembled chassis
●Pre-painted plastic body, complete with markings
●2.4GHz Perfex KT-531P 2.4GHz transmitter
●Front tread adjustment parts set
●Front suspension adjustment spacers
●Pinion gears 6T, 7T, 8T, 9T
●Wheel wrench
●Pinion gear tool
●Spare nuts
●Pairing stick
●Tires, wheels
<Required for Operation>
●AAA-size alkaline batteries x 4 or Ni-MH batteries x 4 for chassis.
●AAA-size alkaline batteries x 4 for transmitter
Long King Pin for MP9 (EP/GP). Essential parts for racing to prevent knuckle arm from dropping during a hard crash. ※Spare/Option parts for MP9 series.
Ride height adjustment spacers for the Fantom EP 4WD and EXT. Can be installed in the front and rear between the axle mount and chassis. Allows 2 different(0.5mm / 1.0mm) lower positions.
High-precision, high-rigidity CNC machined 6061T6 aluminum servo mount.
Controls rear pitching to minimize vibration. Delivers strong direct line running as well as cornering. (Includes silicon oil)
* This product is not compatible with the MM2 motor case
From RC action to urban style, this long T-shirt is a personal statement for any scene. Made by Printstar with heavyweight 5.6-ounce high-quality 100% cotton, the sleeves have a clean silhouette without ribs.
※It is not possible to drive with auto scale alone. In addition, some bodies cannot be mounted depending on the chassis.
※The separately sold LED light unit set (No.MZW429R) cannot be installed on the McLaren Senna GTR.
CNC machined 2.5mm thick carbon front and rear suspension plate, rear side plate set. Lighter and much stronger than normal aluminum
CNC machined 3mm thick carbon shock stay. The strength is significantly improved compared to the normal FRP product.
Exquisite finish and realistic appearance. A complete body series that can be enjoyed as a high-quality display that provides the joy of decorating.
* This product is a spare body set and cannot be run. To enjoy driving as an RC model, please purchase a ready set.
